All In MedTech

Device Trial Radar · NCT03973190

Evaluation of Bone Quality and Primary and Secondary Stability of Implants Installed in Alveolar Regeneration Area by Three Different Techniques

Last checked: Nov 20, 2026Latest source record: Jun 4, 2019 (this record)Source: ClinicalTrials.govMethods & limitations

Status unknown

Status

Status unknown

Enrollment

30

Planned (sponsor's estimate)

Start

Aug 1, 2018

Primary completion

Jun 25, 2020

Study completion Aug 30, 2020

Sponsor

Lead sponsor
Federal University of Juiz de ForaAcademic, hospital or other
Sponsor type
Academic, hospital or other
First posted
Jun 4, 2019

More device trials from this sponsor

Design

Study type
Interventional
Phase
Not applicable (typical for device studies)
Allocation
Randomized
Model
Factorial
Masking
None
Primary purpose
Treatment
FDA-regulated device
No
Who can join
All sexes, from 18 years
Healthy volunteers
Yes

Summary

As written by the sponsor on the registry.

The objective of this randomized controlled clinical study was to compare bone quality between three different alveolar ridge preservation methods, also with the evaluation of primary and secondary dental implant stabilities at these sites.

Conditions

  • Alveolar Osseous Loss

Interventions

  • Immediate alveolar regeneration after exodontiaProcedure

    The extractions will be performed under local anesthesia, without making a mucoperiosteal flap, making an intraassucular incision and using appropriate periotomes, elevators and forcépes, minimizing the surgical trauma of surrounding tissues. Thorough curettage of the alveolus will be performed at the time of extraction to ensure removal of all granulation tissue and stimulate bleeding from the bone base, to form blood clot and promote healing. The sutures will be removed after 7 days of surgery, except for patients in group 3, in which sutures will not be made.

  • installation of dental implant and collection of biological materialProcedure

    The material was collected for histological analysis, extracted with trephine drill of 2.0 mm in diameter. Samples were removed before the incision. A linear incision was then made on the alveolar ridge in the region and flap detachment. The initial insertion of the implant was performed using the contra-angle at 30 rpm, the final insertion of the implant was performed with manual torque wrench, where the insertion torque was measured and the value was tabulated, not exceeding 60 N. cm. The component was installed with a maximum torque of 20 N and SmartPeg® (Integration Diagnostics AB, Göteborg, Sweden) was adapted. The prosthetic component was installed with a maximum torque of 20 N and SmartPeg® (Integration Diagnostics AB, Göteborg, Sweden) was adapted. the tabulated values and the incision was sutured.

  • ISQ analysisDevice

    The prosthetic component already installed. On it is adapted the SmartPeg® (Integration Diagnostics AB, Göteborg, Sweden). According to the manufacturer, the device generates a series of signals with different frequencies in Hertz (Hz) and these values are immediately converted to ISQ (Implantation Stability Coefficient), providing fast and accurate monitoring. The calibration is performed on the buccal and palatal surfaces of the intermediaries, that is, each implant was submitted to 2 readings. The readings were captured and tabulated for further analysis. were repeated at intervals of 7 to 10 days, 30 days and 60 days, for evaluation of SSI in the period of osseointegration. With the objective of not subjecting the implant to torque and torque during this period and to avoid interfering with the osseointegration process, the micro-pillars were covered with the micro-pillar protection screws with digital pressure only.

Primary outcomes

What the sponsor says the trial is designed to measure.

  1. ISQ analysisTime frame: up to the conclusion of the study, an average of 2 years

Locations

1 site in 1 country. Site status is shown where the registry gives one.

  • Programa de Pós-graduação em Odontologia Faculdade de Odontologia - UFJF

    Juiz de Fora, Minas Gerais, Brazil

Contact details for sites and study staff are not shown here. To ask about taking part, use the contact information on the registry record.

For information only. Nothing on this page is investment, legal, tax or medical advice, and nothing here is an offer to sell or a solicitation of an offer to buy any security. The data comes from public government sources, which can be incomplete, delayed or wrong. Check the original record before relying on it.