All In MedTech

Device Trial Radar · NCT03716349

Esthetics of Dental Composite and Adhesive System

Esthetic Outcomes of a Newly Developed Dental Composite and Adhesive System: a Randomized Clinical Trial

Last checked: Nov 20, 2026Latest source record: May 1, 2026 (this record)Source: ClinicalTrials.govMethods & limitations

CompletedResults posted on the registry

Status

Completed

Enrollment

36

Actual

Start

Jan 1, 2019

Primary completion

Nov 20, 2025

Study completion Nov 20, 2025

Sponsor

Lead sponsor
Erica TeixeiraAcademic, hospital or other
Sponsor type
Academic, hospital or other
Collaborators
Tokuyama Dental Corporation
First posted
Oct 23, 2018

More device trials from this sponsor

Design

Study type
Interventional
Phase
Not applicable (typical for device studies)
Allocation
Randomized
Model
Parallel
Masking
Triple (participant, investigator, outcomes assessor)
Primary purpose
Treatment
FDA-regulated device
Yes
Who can join
All sexes, from 18 years
Healthy volunteers
Yes

Summary

As written by the sponsor on the registry.

To compare a newly developed filling composite to a current filling composite system. Two restorations will be placed in each subject, one using system A and one using system B. The first system listed in the randomization pair will be placed on first tooth (#4-#13), and the second system on 2nd tooth (#4-#13). The same three researchers will be responsible for placement of all the restorations.

Conditions

  • Cavities of Teeth

Interventions

  • Pulp vitality testingDiagnostic test

    each tooth will be tested to determine if the pulp of the tooth responds to cold

  • PhotosOther

    Photos of teeth (Photos will be taken with a DSLR camera settings will be determined with optimal settings) and captured periodically throughout the study. Photographs will be made of the cavity preparation. Photographs will be made post-operatively

  • local and/or topical anestheticDrug

    Local and/or topical anesthetic will be applied as necessary to the teeth or gingiva

  • rubber damDevice

    The area will be isolated with rubber dam isolation

  • tooth surface cleanedOther

    The tooth surface will be cleaned with flour of pumice on a prophy cup only, cavity preparation will be performed as usual for caries removal.

  • enamel marginsProcedure

    Enamel margins will be beveled with a long flame diamond bur (8863.314.012 Komet) at 45 degrees to the external tooth surface to achieve the desired bevel length. Along with the use of the diamond bur, infinite invisible margins will be created by contouring and smoothing with a dark orange Sof-LexTM extra-thin contouring and polishing disc (3M).

  • Adhesive SystemsProcedure

    Adhesive systems will be applied according to manufacturer's instructions and selective etching of the enamel will be performed. The dental composite will be incrementally placed using a two- layer or one-layer technique based on the cavity size and light-cured (detailed adhesive instruction sheet will be chairside for reference)

  • cavity preparationProcedure

    The technique to be used will be determined by the size of the final cavity preparation. For small preparations a one-layer technique will be used. No backing material is necessary for the Tokuyama system, Filtek Supreme Ultra will be determined by manufacturer's wheel. A two-layer technique will be used for a large cavity preparation. Large cavity preparation is defined as being 4mm in length or more and/or at least 2mm in depth.

  • Shade selection using Easy Shade 5Other

    A1 (shade determined by Easy Shade 5), ECM-001/Backing material, A1E/A2D (shade will be selected by shade wheel) A4 (shade determined by Easy shade5), ECM-001/Backing material, A3E/A6D (shade will be selected by shade wheel

  • Light CuringProcedure

    A Valo Grand curing unit (Ultradent) with an exitant irradiance with no less than 500 and no greater than 1500 mW/cm2 as measured with MARC Light Collector will be used in standard mode to deliver the required radiant exposure J/cm2 for adhesive and dental composite increments.

  • Contoured and polishedProcedure

    The restoration will be contoured and polished with - Long flame diamond bur (8863.314.012 Komet), Sof-Lex Medium (orange) Contouring and Polishing Discs (3M), Green Jiffy cup pre-polisher (Ultradent Products, Inc.), Blue and grey silicone points composite polisher gloss plus finisher (Kerr Hawe)

  • ConsentOther

    The consent form will be signed, copy will be provided to the patient

  • Health QuestionnaireOther

    The health questionnaire will be completed at initial visit and updated at each follow-up visit

  • xrayRadiation

    When necessary a radiograph (xray) will be obtained

  • Release of medical information signedOther

    The release of medical information form will be signed

  • Oral ExamOther

    An Oral Exam will be completed

  • Teeth AssessmentOther

    The teeth assessment by subject will be completed using the Visual Analog Scale (VAS) and Verbal Rating Scale (VRS) at the follow-up visits 1 month after restoration, 1 year, 2 years and 3 years post restoration.

  • Clinical AssessmentOther

    A clinical assessment will be completed by the evaluators

  • Tokuyama Universal BondDevice

    Tokuyama Universal Bond (TUB) single component self-etching 1-step adhesive system with Tokyuama supra-nanofilled dental composite (ECM) (Tokuyama Dental Corp., Japan)

  • ScotchBondDevice

    Scotch Bond Universal one-step adhesive system with Filtek Supreme Ultra™, nanofilled dental composite (3M)

Primary outcomes

What the sponsor says the trial is designed to measure.

  1. Patient Satisfaction of the Restoration's Appearance (Esthetics) Using the Visual Analog ScaleTime frame: 5 years

Locations

1 site in 1 country. Site status is shown where the registry gives one.

  • University of Iowa

    Iowa City, Iowa

Contact details for sites and study staff are not shown here. To ask about taking part, use the contact information on the registry record.

For information only. Nothing on this page is investment, legal, tax or medical advice, and nothing here is an offer to sell or a solicitation of an offer to buy any security. The data comes from public government sources, which can be incomplete, delayed or wrong. Check the original record before relying on it.